hackshaser.blogg.se

How to edit a border in campaign cartographer 3
How to edit a border in campaign cartographer 3










how to edit a border in campaign cartographer 3

“If the Church were a country, it would be the third most populous, after China and India.” The Church, furthermore, is probably the world’s largest non-state landowner. “There are 1.2 billion Catholics,” she told me. Later, though, as she grew increasingly concerned about climate change, her ambitions broadened, and she began to think of ways in which the Catholic Church could be mobilized as a global environmental force. For a year or two, when she was in college, she considered becoming a nun.

HOW TO EDIT A BORDER IN CAMPAIGN CARTOGRAPHER 3 WINDOWS

On the wall to her right were windows draped with gauzy curtains to her left were enormous fresco maps, commissioned in the early sixteenth century, depicting the world as it was known then.īurhans has been a deeply committed Catholic since she was twenty-one. She took it to the third loggia of the Apostolic Palace, and walked down a long marble hallway. A pair of Swiss Guards, in their blue, red, and yellow striped uniforms, led her to an elevator. He gave her a funny look: the entrance was a few steps away. At last, she spotted a monk, and she asked him for directions. She hadn’t bought a SIM card for her phone, so she couldn’t call for help, and, in a panic, she ran almost all the way around Vatican City. On the day of the meeting, she couldn’t find the entrance that she’d been told to use. To her surprise, she received an appointment in the office of the Secretariat of State. She wanted to discuss a project she’d been working on for months: documenting the global landholdings of the Catholic Church. When she arrived, she got a room in the cheapest youth hostel she could find, and began sending e-mails to Vatican officials, asking if they’d be willing to meet with her. In the summer of 2016, Molly Burhans, a twenty-six-year-old cartographer and environmentalist from Connecticut, spoke at a Catholic conference in Nairobi, and she took advantage of her modest travel stipend to book her return trip through Rome. 1200x1200 gets messy too quickly when having to zoom in but I might be going to far over the limit when saving at 2400x2400.This content can also be viewed on the site it originates from. My maps are 120x120 when I make them in CC3+ so I save at 1200x1200 or 2400x2400 if I want a better picture and I don't care about a 100pixel square in the map. I have GIMP 2.0 so I think I will try this. If you have a very large map, export from CC at the pixels-per-square you want and then cut it into smaller sub-maps in your graphics app.I had not considered converting to jpg in gimp after saving as a rectangular png. You can go a little above this, but don't make a habit of it. Note: the recommendation is to keep FG image dimensions below 2048x2048 pixels. If you have a very large map, export from CC at the pixels-per-square you want and then cut it into smaller sub-maps in your graphics app. It's a lot faster changing JPG quality in a graphics app than it is changing the quality and re-exporting from CC3+. Experiment with the JPG quality setting until you get a small file size with a good-enough visual quality. Load it up in your favourite graphics app and export as a JPG with quality around 60 as the first try - check the file size, you want to get it below 1MB if possible - the lower the file size, the faster it will share with your players. But do not use this PNG in Fantasy Grounds.

how to edit a border in campaign cartographer 3

I usually export to a PNG file as the first step, as it will be high quality (no lossy compression).

how to edit a border in campaign cartographer 3

So if you have a 150 x 200 foot map, export at 1500x2000 pixels. 50 if the map is large, which equates to 10 pixels per foot. Decide on the grid size you want to use - between 50 and 100 pixels per 5' square is usual.












How to edit a border in campaign cartographer 3